Drinkwell® Aqua Cube Pet Fountains

FAQs

• The Pet Fountain seems dirty even after cleaning.

  If there is a white chalky substance in the Pet Fountain, your Pet Fountain may have a mineral deposit build-up from hard water. To remove these deposits, clean the Pet Fountain parts with 80% water, 20% vinegar solution. Rinse all parts thoroughly afterwards. Use filtered or purified water instead of hard tap water to prevent this.

  Close
• The fountain feels slimy.
  • If you have multiple pets or dogs use the fountain, the slimy feeling may be caused by your pet's saliva. Change the water and clean your fountain more frequently to prevent this.
  • Make sure the fountain parts are rinsed thoroughly after cleaning the fountain. Soap residue may cause the sliminess.
  • To reduce mold and mildew, soak the fountain in a 90% water, 10% bleach solution for 15 minutes. Be sure to rinse every part thoroughly before re-assembling the fountain.
  • If there is a white chalky substance in the fountain, your fountain may have a mineral deposit build-up from hard water. To remove these deposits, clean the fountain parts with a 90% water, 10% vinegar solution. Rinse all parts thoroughly afterwards. Use filtered or purified water instead of hard tap water to prevent this.

  Close
• The fountain is leaking.

  Sometimes water around the fountain is caused by pets drinking. Some pets are prone to spilling. Watch your pet when he drinks to see if this is the cause. If it is, you can purchase a fountain mat or other water-resistant mat to place under the fountain.

  • Try to find the leak. Look for visible cracks in the bowl.
  • If there are no visible cracks in the bowl, place the fountain on a towel to see where the leak is.
  • If you find a leak, you can attempt to patch it or call Customer Care about replacing the fountain.
  • If the cord is wet above the water line, loosen the cord and allow some slack so water won't travel up the cord.
  • If you have the Original fountain, you may need to remove the pump to properly clean around it.

  Close
• The fountain is too loud.
  • A low humming noise is normal, but it should not be loud. Some fountains hum a little louder than others.
  • If the water is making too much noise, add water to the fill line and reduce the flow using the flow control knob.
  • If the motor is humming loudly, make sure the water level is above the minimum line.
  • When turning on the fountain or replacing the filter, the motor may make more noise than usual. It should return to normal levels within a few minutes.
  • Unplug the fountain for 15 seconds. If the noise stops when plugged back in, it's possible that some debris is caught on the impeller. Remove the pump and clean the impeller. Try rubbing a small amount of vegetable oil onto the magnetic pin with a cotton bud to lubricate the impeller.
  • Clean your fountain completely. See below for full cleaning steps.
  • Hard water buildup can sometimes cause more noise. Try adding plain white vinegar inside the pump's cavity (without the impeller) and allow it to soak for 10-15 minutes. Allow the impeller to soak in a separate bowl of vinegar for the same duration of time. Clean all fountain parts in soap and water before reassembling the fountain.
  • The Big Dog and Original fountains may be noisier due to a loose impeller pin. Gently but firmly press down on this pin to re-seat it into its proper place in the motor. If the pin has completely dislodged itself from the motor, it cannot be placed back into the motor cavity properly and the motor will have to be replaced. Call Customer Care for information on replacing your motor.

  Close
• The fountain stopped working.
  • There are several possible causes for a fountain to stop working. Sometimes it takes a few minutes for the motor to start pumping water once it's refilled or plugged in. If water doesn't flow after 5 minutes, try these troubleshooting tips:
  • Unplug and re-plug the fountain into the same outlet.
  • Check the cord. If it has any frayed or exposed wires, your pet may have been chewing on the cord. To prevent this, you can purchase a cord cover from most hardware stores. You could also try securing the cord to the floor with duct tape.
  • Clean the pump and motor. Lack of regular cleaning may result in the pump becoming clogged with pet hair and food debris. The pump must be cleaned every 2-4 weeks to ensure proper function.
    1. Remove the motor from the fountain.
    2. Lift the impeller (which looks like a small white propeller) out of the motor. There may be a faceplate cover over the impeller than can be pulled up with a coin or fingernail. Wash the impeller in soapy water, removing hair and other gunk that has collected around it.
    3. Pour soapy water inside the motor cavity and clean with a small round brush like the one found in the Fountain Cleaning Kit. A small toothbrush might work too, or anything that can reach all the way inside the cavity.
    4. Rinse all parts well before returning to the fountain.
  • Water quality can also affect the pump and how well it runs. Hard water will cause calcium deposits to build up in the pump's cavity, blocking the impeller from spinning. If there is evidence of hard water build-up inside the pump, try adding plain white vinegar inside the pump's cavity (without the impeller) and allow it to soak for 10-15 minutes. Allow the impeller to soak in a separate bowl of vinegar for the same duration of time. Clean all fountain parts in soap and water before reassembling the fountain.
  • Make sure the cord does not have any frayed or exposed wires due to pets possibly chewing the cord. If your pet is prone to chewing, visit your local hardware store and purchase a conduit cover to protect the cord.
  • Pumps last for several years with proper cleaning. If the pump has been in regular use for several years, it may be old and need to be replaced.
  • The fountain is to be used indoors only. The fountain parts and pump are not UL approved for outdoor use. Using the fountain outside can damage the pump. If you have used your fountain outside, the pump may need to be replaced.
  • If the pump was exposed to low water levels for a prolonged period of time, the pump's motor may have burned out and the pump may need to be replaced. To prevent this, always keep your fountain water above the fill line.

  Close
• There’s black dirt in the bowl.

  This black stuff is loose charcoal from the filter and is completely harmless for your pet to drink. The charcoal filter is made of organic coconut shells. Rinse the filter in cold water before placing it in the fountain to prevent this. Some filters may shed more charcoal than others due to differing consistency of charcoal in each batch of filters, so don't be surprised if some filters leave behind more charcoal dust than others.

  Close
• The water’s not flowing as much as it used to.
  • Disassemble and clean the pump.
  • Clean the fountain, especially around the motor.
  • Fill the fountain with water up to the max fill line.
  • Check the setting on the flow control knob to make sure it is set to max.
  • With a 360 Plastic or Stainless Steel fountain, the more spouts on the top, the weaker the water flow for each spout. Try switching to a top with one fewer spout opening.

  Close